Nate's 1998 Z28 Project

[nascarnate326]

Here is a vid of the exhaust. Ill have to figure the tips and rasp out after the suspension and other things get taken care of.

[OVRKILL]

Since I have been busy with the bathroom remodel it seems my car has been forgotten about. It hasn't and I have got a couple of things in order.

These are the turn signals I should have ordered the first time. Black background with clear texturized front.

[ATTACH=CONFIG]53328[/ATTACH]

Link?

[nascarnate326]

Link?

http://www.ebay.com/itm/1993-2002-CH...19469d&vxp=mtr

Nothing against the ones you have I just like these better.

[BP_Z28]

I think I have those exact ones sitting in my garage that I wanted to use for my 98, somehow someway moister got inside even after I sealed everything correctly... So just ended up night shading and sanding my stockers

Sent from my C811 4G using Tapatalk

[nascarnate326]

I think I have those exact ones sitting in my garage that I wanted to use for my 98, somehow someway moister got inside even after I sealed everything correctly... So just ended up night shading and sanding my stockers

Sent from my C811 4G using Tapatalk

I sure hope these don't get moisture in them. Getting the headlights in and out is a SOB.

Why not hair dryer yours and seal them again?

[BP_Z28]

I did but just said f*** it

You will probably have way better luck than me, my luck sucks ass

[c0ncEpT]

Start looking for a vacuum leak. I bet thats where your idle surge comes from.

On a side note this is how I had my catch can routed

327239d1322108865-my-catch-can-routing-ok-pcv-1ls1ext.jpg

[OVRKILL]

http://www.ebay.com/itm/1993-2002-CH...19469d&vxp=mtr

Nothing against the ones you have I just like these better.

Me too...hence the request

[nascarnate326]

I did but just said f*** it

You will probably have way better luck than me, my luck sucks ass

Don't say that. Seal them again and get them installed!

Start looking for a vacuum leak. I bet thats where your idle surge comes from.

On a side note this is how I had my catch can routed

[ATTACH=CONFIG]53496[/ATTACH]

Thanks for the pic, looks like mine is installed wrong. Would it be OK to repair a PCV line or just replace it?

Me too...hence the request

Ahh got ya. I wasn't catching what you were throwing.

[c0ncEpT]

Thanks for the pic, looks like mine is installed wrong. Would it be OK to repair a PCV line or just replace it?

You could repair it but for the $3.00 at the auto parts store it would cost for some new hose I don't see why you would bother.

[nascarnate326]

You could repair it but for the $3.00 at the auto parts store it would cost for some new hose I don't see why you would bother.

So its just a regular hose?

The 1998 PCV line on ebay is over 100 bucks, so $3 would be great to fix this problem.

[c0ncEpT]

So its just a regular hose?

The 1998 PCV line on ebay is over 100 bucks, so $3 would be great to fix this problem.

As long as your valve is still intact its just standard hose.

[nascarnate326]

Received my headers today. They look great. Speed Engineering, full 1 3/4 primaries. Will have more goodies showing up later this week.

[sman]

Are you running a catch can? If so which one? I keep procrastinating, need to get one.

[BP_Z28]

A local friend of mine ordered a set of those headers. They look to be nicely done. Not a bad price for stainless also.