Tweet
Yupp so far stock pressure regulator.
I used a die grinder (cut off wheel) but my pump assembly was out when I did it.
I used a die grinder (cut off wheel) but my pump assembly was out when I did it.
-
Originally posted by Yoshi94sigpicOriginally posted by ryanwarby01 -
3 WEEKS MY REAR END AND DRIVESHAFT WILL BE SHIPPED
Argh that was a lot of money.
Originally posted by Yoshi94sigpicOriginally posted by ryanwarby01Comment
-
- Brian Meissen
Owner, MiFBody.com
Administrator, LTxTech.com
1994 Camaro LT1 Transplant -
357ci LT1, cammed, stalled, and driven.
2022 Camaro LT1 - "Cherry Bomb 2"Michigan FBody Meet & Greet Car Show 2022
June 4th, 2022 - 9am to 3pm!!!
The HUB Stadium, Auburn Hills, MIComment
-
Unless you are giving me cash this is not Woot =)Originally posted by Yoshi94sigpicOriginally posted by ryanwarby01Comment
-
Wiring Wiring Wiring and more wiring.
Currently working on the Mallory 685.
Had to extend the harness. Thats finished.
The Ignition side is all wired up.
Left to do is the ground and power.
Mount the box. I am mounting it on the passenger side of the trans tunnel.
Then wire the 2 step into the Clutch switch.
Pics will be coming soon.Originally posted by Yoshi94sigpicOriginally posted by ryanwarby01Comment
-
your going rear mount distributor with a single plain and carb right? what you doing for heads? We NEED PICS!Comment
-
Haha that won't be until I start building the other block laying in the garage.
This is basically getting the car ready
Rear end will be ready, fuel system will be ready.Originally posted by Yoshi94sigpicOriginally posted by ryanwarby01Comment
-
CHRISTMAS IN MARCH!?!??! I THINK SO!
Nevermind the amount of money I've spent in the last month.
Originally posted by Yoshi94sigpicOriginally posted by ryanwarby01Comment
-
Alright so I came home and found these sitting by my garage door. I had no idea I think someone left them there by accident.
DSCN0163.JPGDSCN0164.JPGDSCN0165.JPGDSCN0166.JPGDSCN0167.JPGDSCN0168.JPG
I guess we can go down the list.
- Rear Slicks: MT ET Streets Bias Ply, 28" tall by 12.5", 15" rim.
- Front Runners: MT Sportsman S/R 26" tall by 5", 15" rim.
- Bell Housing: Quicktime thing has to be least 1/2" thick.
- Harnesses: RCI 5 Point harnesses.
- Rear Rims: Weld RTS Forged 15" by 10.275".
- Front Rims: On back order, estimated ship date is 3/25.
Still waiting on other parts to come in.Originally posted by Yoshi94sigpicOriginally posted by ryanwarby01Comment
-
I'm curious to hear how that Quicktime piece fits. Like I said on LS1tech, my McLeod piece is the lowest thing on my car aside from maybe the headers. And not having to cut out for the starter would already make it worth the money since that is some thick steel to cut cleanly with the tools most DIY guys have. It has the engine plate that goes on behind the clutch too, right?Comment
-
It does not have an engine plate.
Looks like its separate if you want one.
http://www.summitracing.com/parts/qt...make/chevrolet
EDIT: Debating on if I should order one.
EDIT EDIT: Just ordered the engine plate also.Last edited by Fox Slaughter; February 26th, 2013, 09:31 PM.Originally posted by Yoshi94sigpicOriginally posted by ryanwarby01Comment
-
More Parts arrived today.
Coilover setup and rear shocks.
Double Adjustable front and rear.
300lbs springs for front coils.
DSCN0169.JPGDSCN0170.JPGDSCN0171.JPGOriginally posted by Yoshi94sigpicOriginally posted by ryanwarby01Comment
-
dang mr money bags!!!1998 Chevrolet Camaro Z28 - 6 SpeedComment
-
More parts arrive today so pictures of those will be put up when I get home.
No no, more like I found change in the couch. Brent is Mr Money Bags.Originally posted by Yoshi94sigpicOriginally posted by ryanwarby01Comment
-
what type of shocks are they? never seen them or heard of them before.Doing less with more
Comment
Comment