Charlyne 95 Z28 M6

[Fox Slaughter]

Was being lazy today. Its hard to get motivated to go outside when I work outside.
I did get the fuel pump assembly back in.
Just need to run the AN lines and the hotwire kit and thats done.
On the plus side did get a bunch more tools for $1.37.
Gotta love points on credit cards.

DSCN0146.JPG

[Fox Slaughter]

New package arrived when I was at work today.

DSCN0147.JPG

Looks like 2 step launches for this season.

[Fox Slaughter]

Well I have the fuel tank back up temp so I can mark the braided lines and cut them.
Still have to wire up the hotwire kit.

Which line is for the vent and which one goes to the charcoal canister?

The long one and the one between the feed/return. What is which?

[Fox Slaughter]

Update:

Pump installed.
AN lines installed.

Need to Install:

Hotwire.
Mallory 685.

DSCN0148.JPGDSCN0149.JPGDSCN0150.JPGDSCN0151.JPG

[mcalus]

Looks good, nice piece of mind too. Seemsl like you need to get the valve covers off and send them out the the powdercoater!!!

[Fox Slaughter]

Yes sir! I was planning on spray painting them Kawasaki green (already did one on my old set) but with the advent of Darren powercoating =).

So items to be powdercoated are:

Rear sway bar.
Rear springs.
Valve covers.
Crotch strap bars.

I'm sure there will be more.

[Fox Slaughter]

Currently in the middle of the Hotwire install.
Got the sender repinned. Solenoid mounted.
Just need to run the harness up into the engine bay and finish the stuff up there.

[Fox Slaughter]

B*tches love Pictures.

DSCN0152.JPGDSCN0153.JPG

Solenoid Mounted.
Sending unit repinned.

Unlike Joel I'll give you pictures =)

[JoeliusZ28]

TJ would you mind if i stopped over and checked out your AN lines in person? Im tempted to go that route anyway yet, what was the total cost?

[Fox Slaughter]

Nope you can. I'm just taking a break watching the Wings game right now.

Um I don't know off the top of my head but I can try to find the receipts. I was tossing around the idea of making these for people.

Looks to be under 300.
The most expensive parts were obviously the AN lines. 85 bucks for 20ft. Need 2 of these.

[Lucky SOB]

Well those certainly look cool!

[Fox Slaughter]

Parts list for AN fuel Lines:

http://www.jegs.com/i/JEGS-Performan...oductId=752578 x 2 = 170

http://www.jegs.com/i/JEGS-Performan...oductId=757777 x 6 = 30

http://www.jegs.com/i/Earls/361/1650...oductId=749418 x 1 = 10

http://www.jegs.com/i/Earls/361/1650...oductId=749418 x 1 = 10

http://www.jegs.com/i/Russell/799/64...oductId=819594 x 1 = 16

http://www.jegs.com/i/Russell/799/64...oductId=819594 x 1 = 15

http://www.jegs.com/i/JEGS-Performan...oductId=760701 x 1 = 29

http://www.jegs.com/i/JEGS-Performan...oductId=763974 x 2 = 18

Optional:

http://www.jegs.com/p/JEGS-Performan...23175/10002/-1 x 1 = 20
-------------------------------------------------------

298. 318 with the vise jaws.

There you go Joel.

[JoeliusZ28]

You da man TJ!

I cant escape the cha-ching sound of the cash register!

[Fox Slaughter]

Eh get use to that sound. It will follow you for the rest of your life.

[JoeliusZ28]

What did you use to cut the lines on the sending unit? Think im safe to use a cutoff wheel if I havent fired the pump yet?

And youre using the stock fuel pressure regulator right?