its a Munster :-D

[s.reef]

Looks good! Jumping back to the fuel pump swap, it is a piece of cake...took me an hour and a half to install it and put the hotwire kit on.

[csmith4153]

lol can i get a exchange i cut a lil much off

LoL, Dont think the warehouse folks would like that.

All merchandise to be returned must be in its original packaging and accompanied by the original invoice. The product must have been purchased from CS3 Automotive and be unused, unaltered, and unchanged from its original state.

[MunsterZ28]

Looks good! Jumping back to the fuel pump swap, it is a piece of cake...took me an hour and a half to install it and put the hotwire kit on.

hmm im really tempted but cash is tight now, gotta buy books

LoL, Dont think the warehouse folks would like that.

lol i was just pulling your chain, i knew as soon as i pulled the cutter out i was committed

[csmith4153]

Auto Meter woudnt need to change the mold much to make it fit the 93-97 cars.

[BLKHAWK]

well i got the bottle mounted and and the lines run, waiting for my old shop teacher to fab me up relocation brackets because nitrous works didnt want to sell me them , anywho heres a few pics and o ya gotta stop the project for some bday cake me n my sis on my 19th bday the other day. idk if you can see it in the first pic but i mounted the bottle so it rested on the floor, well i had an idea and got some cheap floor mats at wal-mart cut them to fit and now the bottle sits on the floor mats and there will be no rattles or metal to metal contact. i dont no if anyone else did it but for a breif moment i felt smart

you need a single stage switch, and is this how your gonna mount the bottle?
its supposed to be on a 45 degree angle.

[MunsterZ28]

you need a single stage switch, and is this how your gonna mount the bottle?
its supposed to be on a 45 degree angle.

o the pic in the install directions showed a 45 or straight up and down, as long as the bottle faced a certain way, yes i need a single switch, i have a order in with dynotune for one but my card information got screwed up, still trying to sort it out.

[MunsterZ28]

Auto Meter woudnt need to change the mold much to make it fit the 93-97 cars.

actually this one fits a 97, diffrent dash style. i think they dont because 93-96 is three years and theres most likly not a huge demand for them

[my95z28]

Looks pretty good! As far as the order of the mounting them, I would find whichever one is closest to bieng level with your head, and mount the shift light there. The other two I dont think it really matters where you put them.

[JoeliusZ28]

actually this one fits a 97, diffrent dash style. i think they dont because 93-96 is three years and theres most likly not a huge demand for them

looks like creight is aware of that

[csmith4153]

Yes, It was a typo - ment to type a "6" not a "7"
I own a 94 and a 99 Camaro, so I have both different dashes.

[MunsterZ28]

looks like creight is aware of that

Yes, It was a typo - ment to type a "6" not a "7"
I own a 94 and a 99 Camaro, so I have both different dashes.

i figured it was just a typo, anybody have any tricks on how to wire these gauges, the instructions say to cut a whole threw the firewall but im just wondering if anyone has done it diffrently before i hack to it

[Boost Addict]

Mines through the firewall.

[MunsterZ28]

where did you put the hole? thats another issue i ahve

[Boost Addict]

I forgot right off hand but if I saw a picture i could give you a relative idea. It really doesnt matter just make sure you dont run into anything in the engine bay. The hard part is getting the wires from the pillar under the dash.

[MunsterZ28]

I forgot right off hand but if I saw a picture i could give you a relative idea. It really doesnt matter just make sure you dont run into anything in the engine bay. The hard part is getting the wires from the pillar under the dash.

thats my thing is i dont wanna run into anything, hmm well i got a day to figure it out i have work tomorrow lol cash for the project