Announcement

Collapse
No announcement yet.

some of my winter projects

Collapse
X
Collapse
Who has read this thread:
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Car is done and insured! just took it for a quick drive to brake-in the new pads.

    IMG_7093.JPG

    IMG_7094.JPG

    IMG_7095.JPG

    IMG_7096.JPG

    IMG_7097.JPG

    IMG_7098.JPG

    So everything i did this winter:
    • Smoked Corner Lenses
    • Painted the undercarriage completely
    • new passenger front wheel bearing
    • new pinion seal
    • new axle seals
    • tubular panhard rod
    • T/A cover
    • new tie rod end
    • new brakes on all four corners: raybestos rotors w/hawk pads
    • im sure im forgetting some other things...


    Still waiting to be done:
    • Wideband O2 sensor
    • Wheel Project
    • SS Spoiler (repair and paint)
    • electric water pump
    • Cam Swap..dont have this yet


    I need to take it to get it aligned now after doing the tie-rod end, but its not bad and at least its driveable for now, i couldnt be happier (less a cam swap )

    -Joel
    1995 Z28 M6 - AI226/234 - autocross ricer
    1984 Scottsdale K10 - 305/4bbl/4spd


    WTB List:Midwest Chasis DS Loop

    Comment


    • Congrats!!
      Nick H.
      Current MIFC Vice President

      sigpic

      Comment


      • Car looks great. I'm pretty jealous at how well you cleaned everything up underneath. I'm going to give that metal cast pant a try later next week on some parts. Once you get those wheels finished your car is going to steel all the attention from everyone else at meets.


        1997 Trans Am

        www.fquick.com/transampimp

        Comment


        • Originally posted by transampimp View Post
          Car looks great. I'm pretty jealous at how well you cleaned everything up underneath. I'm going to give that metal cast pant a try later next week on some parts. Once you get those wheels finished your car is going to steel all the attention from everyone else at meets.
          thanks man. believe me it was a LOT of work though, im glad i never have to do it again.
          -Joel
          1995 Z28 M6 - AI226/234 - autocross ricer
          1984 Scottsdale K10 - 305/4bbl/4spd


          WTB List:Midwest Chasis DS Loop

          Comment


          • Congrats on having the car back on the road. Too bad your on the wrong side of the state....or maybe I am.
            1998 Chevrolet Camaro Z28 - 6 Speed

            Comment


            • Looks great...how hard was it to replace the tie rods?
              2011 Ford Raptor SuperCrew
              SVT Beadlock Wheels
              Roush Intake, Corsa Exhaust
              20" and 40" Light Bars

              2000 Camaro Z28
              Stripped Down Drag Car Build

              Project 1999 Camaro Z28


              2009 G8 GT Stryker Blue Metallic-SHEGONE
              Crate LS3, LS9 Cam, LSA Supercharger, Metco Solid Isolator
              RotoFab Intake, HSRK, Camaro Trans Pan
              ZL1 HX, ZL1 Fuel Pump, CTS-V Lid, LSA Injectors
              Pat G - 93 Octane Tune
              Kooks 1-7/8" Longtubes, High Flow Cats, X Pipe, Solo AxleBacks
              CTS-V Calipers, Brembo Pads
              H&R Lowering Springs, Whiteline Bushings, FE3 Struts/Shocks, Camaro 20" Wheels
              HIDs, LED Conversion, Atari Gauges, Tint, Roof Carbon Fiber Wrapped, Innovative Wideband

              2.55 Lingenfelter Pulley and Injectors waiting to go on!
              sigpic

              Comment


              • Originally posted by s.reef View Post
                Looks great...how hard was it to replace the tie rods?
                i just replaced the end, it was a piece of cake really.
                -Joel
                1995 Z28 M6 - AI226/234 - autocross ricer
                1984 Scottsdale K10 - 305/4bbl/4spd


                WTB List:Midwest Chasis DS Loop

                Comment


                • Look'in good, Joel!! Can't wait to see it in person!!
                  West Michigan Pontiac Club



                  "A Camaro looks like it can kick your a**, a Trans Am is coming over to do it"

                  Comment


                  • Originally posted by 92conv View Post
                    Look'in good, Joel!! Can't wait to see it in person!!
                    thanks and thanks for your help today!
                    -Joel
                    1995 Z28 M6 - AI226/234 - autocross ricer
                    1984 Scottsdale K10 - 305/4bbl/4spd


                    WTB List:Midwest Chasis DS Loop

                    Comment


                    • Originally posted by JoeliusZ28 View Post
                      thanks and thanks for your help today!
                      Glad to help!! Thank you, too!!
                      West Michigan Pontiac Club



                      "A Camaro looks like it can kick your a**, a Trans Am is coming over to do it"

                      Comment


                      • dude I want to copy EVERYTHING you did to your car.... but that would be gay, so i'll just say nice car!!

                        2011 Mustang GT
                        20" Satin Black AMRs with 305/35 & 275/35 MT Street Radials, Saleen Grille, CS Lower Valance, Roush Axleback, GT500 Spoiler, resonator delete

                        In Progress: Brembo 6-piston brake upgrade


                        Comment


                        • Originally posted by k0261886 View Post
                          dude I want to copy EVERYTHING you did to your car.... but that would be gay, so i'll just say nice car!!
                          lmao thanks man, you have good taste
                          -Joel
                          1995 Z28 M6 - AI226/234 - autocross ricer
                          1984 Scottsdale K10 - 305/4bbl/4spd


                          WTB List:Midwest Chasis DS Loop

                          Comment

                          Working...
                          X