Tweet
I should move mine haha. Mine i think is in the lowest mounting hole.
-
Originally posted by Yoshi94sigpicOriginally posted by ryanwarby01 -
What hole would a lowered car like mine use? Need to get mine in next weekend.1998 Chevrolet Camaro Z28 - 6 SpeedComment
-
More than likely the bottom hole. You really need to get an angle finder on it tho. Like Larry said 0-4 is ideal. It has more to do with instant center than anything. The more angle you have on the LCA the further back your moving the instant center.Originally posted by nascarnate326 View Post
Comment
-
My lca angles are negative even with my 4x4 height
-Joel
1995 Z28 M6 - AI226/234 - autocross ricer
1984 Scottsdale K10 - 305/4bbl/4spd
WTB List:Midwest Chasis DS LoopComment
-
which way do you consider negative?Comment
-
the angle is such that it will want to squat under throttle. the chasis end is lower than the axle end.Last edited by JoeliusZ28; May 13th, 2012, 08:21 PM.-Joel
1995 Z28 M6 - AI226/234 - autocross ricer
1984 Scottsdale K10 - 305/4bbl/4spd
WTB List:Midwest Chasis DS LoopComment
-
I added them to mine on my lowered car (strano suspension) along with tubular LCAs and gained wheel hop... thinking I need to move them up to the higher hole2000 Trans Am l 1967 Firebird
sigpic
Comment
-
I also think a torque arm is a pre-req to this mod unless you are doing it to compensate for a drop kit. I have a set or reloc brackets sitting on the shelf, I dont plan on installing them until the torque arm is in.-Joel
1995 Z28 M6 - AI226/234 - autocross ricer
1984 Scottsdale K10 - 305/4bbl/4spd
WTB List:Midwest Chasis DS LoopComment
-
If you remember, mine is on the top hole... its the same angle it was at stock height, which if you look under my car. it has a slight angle, when i sit in it its mostly likley level. Check your current angle, it should be level or slope slightly downward to your axle.Originally posted by nascarnate326 View Post
2001 Bright Rally Red Camaro SS - M6, Livernois Stage 3 ported 243 heads, Livernois 230/236 114 LSA cam, FRPP 36# injectors, Ported TB, SLP MAF, Volant CAI, Kooks 1 3/4 headers & ORY, GMMG Cat-back. Koni SA 4/3's, BMR springs, Founders Performance, STB, LCA's and Panhard bar.Comment
-
Just put my car on much more level ground. Had my dad sit in it. It was reading 5* unloaded, and 4* with him in it.sigpic
1996 Base Model
+2 cylinder modComment
-
I installed myn with the new torque arm it made a very large improvement in traction . Im using the bottom hole I also have a 1 3/4 inch drop . And I also added more gear and still gained more traction.sigpic1997 firehawk # 115 6 speed. Its just a little ole LT1Comment
-
Made it to the track today.
Had a best 60' of 1.77 best before was 1.89
Also found out my rims are spinning about 1.5" inside the tire each run
On a side note, my dad got his new best 60' too.
1.21Last edited by jderry; May 19th, 2012, 07:18 PM.sigpic
1996 Base Model
+2 cylinder modComment
-
what tires and how much airComment
-
Comment
-
they shouldnt spin
mine worked best at 20-22. i daily drive them at 22Comment
Comment