1991 Camaro Z28 1LE project

[s.reef]

That wire loom is awesome

[JasonH]

1383461_10152756017196850_1740757593838727158_n.jpg
Heater hoses finally done after getting the 90 degree elbow for the heater core


10923507_10152756017381850_3555803246423199871_n.jpg
Battery cable routing


11008543_10152756016996850_3243523052994388931_n.jpg
Power steering pump on



11069618_10152756017331850_1007979051133924308_n.jpg
Starter wires tied up so they don't melt on the header.

11156286_10152756017141850_6156221653715352997_n.jpg
Modified the power steering bracket so I could pass wires behind it.

11169867_10152756016941850_3069072329835284020_n.jpg
Modified power steering bracket.

[mikewoods]

Good work Jason. The car is coming together nicely. Can't wait to see it out on Woodward soon.

[SSTODD]

Unbelievable! Nice work and detail.

[s.reef]

Is this thing done yet?!? Jk we need more pics

[OVRKILL]

Dammit.....a third gen I can't hate.

[1BADAIR]

I make little L brackets from alum stock . Big hole for the bellhousing bolts and two little holes on the other side to run a tie thru to hold the wires

[JasonH]

Is this thing done yet?!? Jk we need more pics

It's a staggering amount of work and parts to get this thing going. I'm waiting on the headers back from the coater. I have a few more cooling system changes to make and I had a power steering pressure hose made by Fluid Systems. One more trans thing to finish up. I still need an exhaust system and a BMR torque arm. I'm working on getting the front end together so I can install the TPI snorkel and figure out what kind of couplers I need for the air intake system.

[Iroc'nthe87]

install the TPI snorkel

Don't choke that engine!

[JasonH]

Don't choke that engine!

I'm aware that it could really choke the engine, but a OEM look is more important to me than power right now. I want it to look like GM built the car for SEMA in 1991, but for using today's technology. In the future I could always build something else.

[JasonH]

Custom power steering line from Fluid Systems
11162511_10152774282876850_1075133031075002244_n.jpg

Power steering system completed
11140402_10152774283041850_63391701529335508_n (1).jpg

Installed the PCM in the OEM location. Tied up right side dash wiring
11182185_10152774283376850_9041783433933053789_n.jpg

I didn't like the way I did the fitting into the radiator for the steam vent. I changed it to a 90 degree fitting so the hose is going in the correct direction.
11041703_10152774283461850_5112509512501720836_n.jpg

[fuelman]

man you do nice work looking killer

[s.reef]

Lookin good

[JasonH]

10403064_10152778832871850_9109917146561114195_n.jpg
LS3 intake sound attenuation cover primed, sanded, primed, sanded and ready for paint.

[JasonH]

Hawks headers back from coating. O2 sensors crash into the trans so I guess I'll be welding new O2 bungs into freshly coated headers.
10409150_10152782235166850_944883868249330525_n.jpg


Modified shift selector arm. I drilled out the ball stud on the bottom and bolted in the ball stud from the 700R4 to accept the 3rd gen shift cable.
11148553_10152782235246850_1515535833137138334_n.jpg