its a Munster :-D

[MunsterZ28]

pulling them off and taking it to a shop will probably still be cheaper and better anyway then getting a different set... it just takes patience... not your going to be driving the car for a while since winter is here

ya i jus found a set that are supposidly ported and polished for a good deal. id have to go check them out

If you're willing to do the drive, Fred, give Steve (BLKHAWK) a PM or call. He had my bolt drilled out and helicoiled, my valve springs installed, and the bowls ported at the same time for like $250. The guy also checked my valves to make sure they were sealing good and didn't need an angle job. But he can get head work done real cheap for you.

lol steve is going to be doing my tune this spring aswell. lol looks like ima get to no him, thanks brian

[bri2203]

anybody want this piece of shit. im at wits end with this

sure, just sign the title over

[MunsterZ28]

picked up a ford product for my car today.
































bye bye 10 bolt

[white97z28]

picked up a ford product for my car today.
































bye bye 10 bolt

So what did you trade your car for a mustang or something!!! lol

[kammi10]

thought u were sellin the car ?

[DETROITMUSCLE]

damn didn't know you had those plans, thats badass. Where did you get it?

[white97z28]

So what did you trade your car for a mustang or something!!! lol

only messin with ya fred...seriously tho thought u were selling it?...well any ways, details on the rear end???

[MunsterZ28]

thought u were sellin the car ?

its still for sale. but i havnt had one bite. to be honest theres not a market for my car with the miles it has. so ill keep budget building.

damn didn't know you had those plans, thats badass. Where did you get it?

yaa off of motown. guy in farmington hills. its not a 9 but its a ford 8.8. ive done alot of research and these rear ends are very cheap to build and are very solid and realiable. a guy on tech built one for $600 and it holds 5k clutch dumps on mickey ts.

got the housing out of a 94 stang for $35 and a 31 spline carrier out of a 03 cobra for $100.

heres the thread http://www.ls1tech.com/forums/gears-...8-8-build.html

--Double post auto merged--

only messin with ya fred...seriously tho thought u were selling it?...well any ways, details on the rear end???

lol i know. i was trying to. see above post.

[DETROITMUSCLE]

yaa off of motown. guy in farmington hills. its not a 9 but its a ford 8.8. ive done alot of research and these rear ends are very cheap to build and are very solid and realiable. a guy on tech built one for $600 and it holds 5k clutch dumps on mickey ts.

got the housing out of a 94 stang for $35 and a 31 spline carrier out of a 03 cobra for $100.

heres the thread http://www.ls1tech.com/forums/gears-...8-8-build.html

I've seen that build before, if you can weld and do your own fab work or get it done for dirt cheap thats the only way it would even be worth it. He even says in there that it was a lot of work. I hope it works out though, its a mini ladder bar and that is something relatively new to 4th gens. It also would suck having to swap out your wheels to a ford bolt pattern.

[ThreeHonks]

IMO its totally not worth the hassle to swap an 8.8 in. Or esle there would be hundreds of cars with them

[MunsterZ28]

moser makes axles to keep chevu pattern. and for just a drag radial car it will b just fine. and yes im going to fab it all up myself.

[DETROITMUSCLE]

thats sweet I had no idea you knew how to weld, good luck and I hope it works out so you can make one for me when your done

[MunsterZ28]

thats sweet I had no idea you knew how to weld, good luck and I hope it works out so you can make one for me when your done

lol ya ill keep everyone tuned in. i prob wont start this til the end of feb or march after i gather all the parts. f*** min wage and still needing a clutch

[bri2203]

thats sweet I had no idea you knew how to weld, good luck and I hope it works out so you can make one for me when your done

I would leave welding axle housings and brackets on to the professionals.
I have welded everything on my chevelle, but if I were todo an axle I would tack them and have a buddy tig them the rest of the way.

You don't want to end up like this http://www.youtube.com/watch?v=hq5rBa4S34I

lol ya ill keep everyone tuned in. i prob wont start this til the end of feb or march after i gather all the parts. f*** min wage and still needing a clutch

D&E in Hazel Park should be able to get you clutch for a decent price(they also carry centerforce). Call them up and if the price is reasonable I can buy it because I get a discount there to save ya a few bucks.

[MunsterZ28]

i just bought a used QTP e-cutout off tech was wondering how people like these? negatives and positives about it. ive heard of motors dieing in certain cutouts but from what i remember qtps are pretty nice?