FS: 5.3l

[1Bad86Iroc]

Non running and currently torn apart.

I got this motor just about a year ago with intentions of doing a build. I've decided against it as I've already put 2 grand into another motor.

I don't know anything about this motor. I believe its an 01. Has a 24 tooth reluctor wheel on the crank. Crank needs to be turned and polished.

What's included:
Block, rods/pistons, front and rear covers, aluminum heads with stock valve springs and a bag of bolts for it.

Does not include:
Oil pan, intake, valve covers, accessory drive or any electrical components.

I don't have any pics of it, but I'm sure we all know what a bare block looks like.

I'll start the price at $200. I can deliver within a reasonable distance. I'm located in Waterford at M-59 and telegraph.

If your interested, send me a PM and I'll send contact info.


Thanks, Toney.


Sent from my DROID RAZR using Tapatalk 2

[Gregs_gsxr]

GLWS...however a picture speaks a thousand words. Anyone is more likely to spark interest if they see what their about to come look at.

your price with in reason, IF it looks good for what you have listed

[TylerT/AZ28]

sounds a wee bit rough how are the mains, bores etc.

[1Bad86Iroc]

Re: FS: 5.3l

Bores and mains all look good. It was oiled down pretty good when I got it.

I'll grab pics tonight when I get it out. I have somebody coming to look around 7

Sent from my DROID RAZR using Tapatalk 2

[1Bad86Iroc]

Re: FS: 5.3l











I'll get more detailed pics of the bores, pistons and crank tomorrow morning.

Sent from my DROID RAZR using Tapatalk 2

[1Bad86Iroc]

Re: FS: 5.3l







Sent from my DROID RAZR using Tapatalk 2

[Gregs_gsxr]

FYI...you should never lay a crank down on its side, stand it on end or hang it, however you shouldnt have a hard time getting 2 bills for it

[1Bad86Iroc]

Re: FS: 5.3l

FYI...you should never lay a crank down on its side, stand it on end or hang it, however you shouldnt have a hard time getting 2 bills for it

Was planning to get a new crank, which is why its in that condition.

Bump.

I'm sure $200 is a steal. The motor is super clean!

Sent from my DROID RAZR using Tapatalk 2

[Gregs_gsxr]

if I didnt just pick up a 2006 pace enclosed trailer, I would think to pick this up for a spare

[1Bad86Iroc]

Re: FS: 5.3l

Shoot me an offer. Worst I can say is no

Sent from my DROID RAZR using Tapatalk 2

[Gregs_gsxr]

this is true and your in my backyard too, I actually dont want to have anything else in the garage right now, and I havent built a shed yet. I need my garage as clean as possible...cause shhh, Im getting close to painting my camaro

[1Bad86Iroc]

Re: FS: 5.3l

I hear ya. One thing after another keeps getting in the garage. Got a pair of tires last night and of all places they end where there is no room...the garage! If you change your mind, let me know!

Sent from my DROID RAZR using Tapatalk 2

[Gregs_gsxr]

For sure!

[beertestr]

Re: FS: 5.3l

I'll vouch for the motor. I did the teardown and hot tank on the block rods and pistons before Toney got it from me. Crank can be used as is, there was a little bearing material on one of the journals that polished out. A 10/10 grind would be insurance, but not really needed.

I got the motor as a running takeout from CARS. It was pulled due to a knock, Sean pet me pull the caps and check the bottom end and we found nothing wrong with the bearings aside from a little bearing material on the journal. I found a bad lifter when I tore the motor down for hot tank. It's likely the bearing started to lose oil film when lifter went bad (typical oil feeds to the crank from the lifter feeds, kill a lifter and the nearby main loses some oil pressure).
Lifter bores are fine, the cup inside the lifter went bad.
I sold the motor after I got rid of my LS Swapped 94 z71, this motor was supposed to upgrade the 4.8 in the truck.

Sent from my DROID BIONIC using Tapatalk 2

[pferris]

Might know some one interested in this. Will half to ask them what they think of it. Would be going in a rx7