Announcement

Collapse
No announcement yet.

Where to put manual fan switch?

Collapse
X
Collapse
Who has read this thread:
 
  • Page of 2
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • #1

    Where to put manual fan switch?

    I opted to make my own rather than pay for an slp one.

    So far I have two 12v LEDS with built in resistors
    DPDT switch (center off)

    And black and red wire.



    Just not sure if I want it out in the open or not
    sigpic

    1996 Base Model
    +2 cylinder mod
    Tags: black, built, car, cen, center, con, controller, fan, hood, leds, make, manual, market, mount, open, pay, put, red, rips, roller, set, slp, switch, temp, wire
  • #2
    why not just put in an after market fan controller, trips by the temp you set it to and its all under the hood.
    '91 Camaro Modded, LSx, House of Kolor Intense White, lowered, GS chrome 18" wheels, 14" Brembo CTS-V on all 4 corners, LS rear end, FP suspension components

    " When in doubt...throttle out ! "
    ENVYsion Entertainment Group

    Comment

    • #3
      Originally posted by Gregs_gsxr View Post
      why not just put in an after market fan controller, trips by the temp you set it to and its all under the hood.
      I want it for use at the track mostly, with the car off, also the SLP one is $70. I can put my switches underhood, but not too sure yet.
      sigpic

      1996 Base Model
      +2 cylinder mod

      Comment

      • #4
        I wouldnt mount them under the hood, but if you can fab up a nice switch plate, down and out of the way, that would be useful
        '91 Camaro Modded, LSx, House of Kolor Intense White, lowered, GS chrome 18" wheels, 14" Brembo CTS-V on all 4 corners, LS rear end, FP suspension components

        " When in doubt...throttle out ! "
        ENVYsion Entertainment Group

        Comment

        • #5
          Mine is in the ash tray good spot if you don't smoke and it doesn't get triped by mistake.

          Comment

          • #6
            Originally posted by slp ss View Post
            Mine is in the ash tray good spot if you don't smoke and it doesn't get triped by mistake.
            good idea !
            '91 Camaro Modded, LSx, House of Kolor Intense White, lowered, GS chrome 18" wheels, 14" Brembo CTS-V on all 4 corners, LS rear end, FP suspension components

            " When in doubt...throttle out ! "
            ENVYsion Entertainment Group

            Comment

            • #7
              Originally posted by slp ss View Post
              Mine is in the ash tray good spot if you don't smoke and it doesn't get triped by mistake.
              Thats where my SLP fan switch is. Perfect location.
              1998 Chevrolet Camaro Z28 - 6 Speed

              Comment

              • #8
                I mounted mine switches in the ashtray made a plate out of plastic small screws hold it in place..firebird 009.JPG
                sigpic
                1998 Trans Am Convertible A4 - WS6 hood, WS6 air lid, WS6 rims, drilled/slotted rotors.

                Comment

                • #9
                  I figured mine out and it turned out nicely, post pics tomorrow.
                  sigpic

                  1996 Base Model
                  +2 cylinder mod

                  Comment

                  • #10
                    HPIM1297.JPGHPIM1296.JPGHPIM1299.JPGHPIM1300.JPG
                    I used some vht niteshade on the leds to make them black when not on, Red is low fan, Red + Green is high
                    sigpic

                    1996 Base Model
                    +2 cylinder mod

                    Comment

                    • #11
                      Nice job!
                      Gone but not forgotten: 1986 Chevrolet Camaro IROC-Z

                      "You shall ride eternal. Shiny and chrome."

                      Comment

                      • #12
                        Did you spray night shade over the hole thing? its looks purple in some of your pics
                        '91 Camaro Modded, LSx, House of Kolor Intense White, lowered, GS chrome 18" wheels, 14" Brembo CTS-V on all 4 corners, LS rear end, FP suspension components

                        " When in doubt...throttle out ! "
                        ENVYsion Entertainment Group

                        Comment

                        • #13
                          Nice Job!
                          sigpic
                          1998 Trans Am Convertible A4 - WS6 hood, WS6 air lid, WS6 rims, drilled/slotted rotors.

                          Comment

                          • #14
                            I just sprayed the leds. I did whipe the whole thing down with some stuff my dad got from work, they use it to detail used cars.
                            sigpic

                            1996 Base Model
                            +2 cylinder mod

                            Comment

                            • #15
                              Originally posted by jderry View Post
                              [ATTACH=CONFIG]36727[/ATTACH]
                              I used some vht niteshade on the leds to make them black when not on, Red is low fan, Red + Green is high

                              It looks purple in this pic, just wondering, post up after you get it installed too.
                              '91 Camaro Modded, LSx, House of Kolor Intense White, lowered, GS chrome 18" wheels, 14" Brembo CTS-V on all 4 corners, LS rear end, FP suspension components

                              " When in doubt...throttle out ! "
                              ENVYsion Entertainment Group

                              Comment

                              Previous 1 2 template Next
                              Working...
                              X