jderry's 1996 Camaro

[Fox Slaughter]

http://forums.corral.net/forums/nitr...us-filter.html

[jderry]

My girlfriend thinks I have a problem =)
GOPR0001.JPG

[Fox Slaughter]

Do you want me to build this car for you too? Jeez I gotta do all the research for you

No you're just a man.

[jderry]

Haha are you offering?
I am just getting ready to be able to work on it again.
Was getting sick of it last year after building the engine, transmission and all of the suspension work.
I was reading some conflicting info about the filter. Not sure what difference it'd make but it'll go right before the solenoid block.

[Fox Slaughter]

You'd have to ask one of the nitrous experts on here. I don't know jack about it haha.
I read one that said by the bottle that says by the noids.
If you pay for all the parts I just ordered I'll work on your car.
Cant guarantee it won't blow up though.

[jderry]

I am thinking of doing an ABS delete as well, any opinions on this?

[c0ncEpT]

I am thinking of doing an ABS delete as well, any opinions on this?

Yes. We are more than likely going to make our own on the blue car while the motor is out.

[jderry]

Is the SJM kit quality? Anything better or most cost effective out there. Is it a bad install with engine in the car?

[c0ncEpT]

Is the SJM kit quality? Anything better or most cost effective out there. Is it a bad install with engine in the car?

The SJM kit is good.

We just plan on doing it for half the price of the SJM kit.

You can easily install it with the motor in the car. We are more than likely going to run all the lines straight down out of the master to clean up the engine bay.

Here is a thread to give you an idea of what some guys do

http://ls1tech.com/forums/drag-racin...bs-delete.html

[Fox Slaughter]

I have the SJM kit. Did it with the engine in.

Did you figure out what slicks you are getting?
I need to decide if I want to exchange mine.

Mine are 28x12.5x15 ET Streets. The tread is 10" the section is 12.5".
28x10.5x15 ET Drags have a 10" tread but a 11.6" section.

So people are telling me why on earth would I need a 12.5" slick, but they keep thinking its the tread not the section. So I have no idea if they will fit, if you mount them you can't exchange them.

[DETROITMUSCLE]

I am not a slick tire expert but I don't think the 12.5 tire will fit without some major work.10.5 will be more than you will prob ever need.

[jderry]

I have the SJM kit. Did it with the engine in.

Did you figure out what slicks you are getting?
I need to decide if I want to exchange mine.

Mine are 28x12.5x15 ET Streets. The tread is 10" the section is 12.5".
28x10.5x15 ET Drags have a 10" tread but a 11.6" section.

So people are telling me why on earth would I need a 12.5" slick, but they keep thinking its the tread not the section. So I have no idea if they will fit, if you mount them you can't exchange them.

I got the 26x11.5x16s I will probably get the sjm kit soon.

[Fox Slaughter]

Hm Hm Hm.

Did you get that kit on yet?

[jderry]

Hm Hm Hm.

Did you get that kit on yet?

What kit? The ABS delete? Or the NX? I won't be installing the kit for a bit. I still need to decide where to put my 685 too.

[Fox Slaughter]

I'm putting mine on the trans tunnel passenger side.

Why?

RACECAR!

EDIT:

Also can't remember exactly but I think the ABS unit weighs like 12lbs.