Announcement

Collapse
No announcement yet.

STARTING TO ADD HORSE POWER NEED HELP

Collapse
X
Collapse
Who has read this thread:
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #16
    A good exhaust - block to tips - will set you back around a thousand bucks.

    1998 Camaro Z28 - Bright Red, 6.0 TR224, 4l60e, 3.42 Eaton TrueTrac
    1989 Camaro IROC-Z Convertible - 355 big tube TPI, WC T5, 3.42 Zexel Torsen, CTS-V/C4 brakes
    1955 Bel Air 2 Door Post - 357 TPI, Muncie M20, 4 wheel disc

    2006 Saab 9-7x 5.3i Daily Driver

    Comment


    • #17
      Hence buying used...

      75% of the stuff in my SC setup was used. Buying all of that new would have cost twice as much.
      Gone but not forgotten: 1986 Chevrolet Camaro IROC-Z

      "You shall ride eternal. Shiny and chrome."

      Comment


      • #18
        Originally posted by MP81 View Post
        Hence buying used...

        75% of the stuff in my SC setup was used. Buying all of that new would have cost twice as much.
        where do you find good used stuff?
        GO BLUE
        sigpic

        Comment


        • #19
          Originally posted by bogeywon View Post
          where do you find good used stuff?
          Craigslist, ebay, or the classifieds on sites like this one.
          Gone but not forgotten: 1986 Chevrolet Camaro IROC-Z

          "You shall ride eternal. Shiny and chrome."

          Comment


          • #20
            I live in Clinton twp and have the tuning software.
            Originally posted by Yoshi94
            Mines about an inch bigger than Kyles. I need to get one of those
            Originally posted by ryanwarby01
            Put it this way, if you have a money tree a LT1 is a wood chipper!
            sigpic

            Comment


            • #21
              I have a set of Hooker headers I'm looking to sell
              2015 Silverado

              Originally posted by JoeliusZ28
              If you need 6 and half grand to break your tires loose you shouldnt be attempting a holeshot.

              Comment


              • #22
                The best bang for the buck on my old 4th gen were drag radials, 3.73 gears, under drive pulleys and a Dyno tune.

                If i could do it again I would say Save your money on all that other crap. If you want to go fast, find an lt4 cam and heads and take that to a reputable shop. Have it Dyno tuned. Get a good stall converter and trans cooler. Drag radials. Own mustangs. Do it right the first time.

                Comment


                • #23
                  Originally posted by Fox Slaughter View Post
                  I live in Clinton twp and have the tuning software.
                  What would it take to change my Speedo for my gears??

                  Sent from my Pantech Breakout using Tapatalk
                  1994 Formula - http://www.fquick.com/garages/viewvehicle.php?id=52284

                  http://freepatriot.org

                  Comment


                  • #24
                    Originally posted by OneMeanFormula View Post
                    What would it take to change my Speedo for my gears??

                    Sent from my Pantech Breakout using Tapatalk
                    Less than 5 mins.

                    Gears 4.10 for manual.
                    3.73 for auto.

                    You can gain extra ponies by doing a valve trainswap. I mean by switching out your rockers to 1.6 and springs.

                    Dont get underdrive pulleys.

                    Free mod remove weight.
                    I removed 80lbs so far between the AC and the spare tire/jack.
                    Last edited by Fox Slaughter; August 22nd, 2012, 09:36 PM.
                    Originally posted by Yoshi94
                    Mines about an inch bigger than Kyles. I need to get one of those
                    Originally posted by ryanwarby01
                    Put it this way, if you have a money tree a LT1 is a wood chipper!
                    sigpic

                    Comment


                    • #25
                      Originally posted by Fox Slaughter View Post
                      Less than 5 mins.

                      Gears 4.10 for manual.
                      3.73 for auto.

                      You can gain extra ponies by doing a valve trainswap. I mean by switching out your rockers to 1.6 and springs.

                      Dont get underdrive pulleys.

                      Free mod remove weight.
                      I removed 80lbs so far between the AC and the spare tire/jack.
                      Anything as far as money??

                      Sent from my Pantech Breakout using Tapatalk
                      1994 Formula - http://www.fquick.com/garages/viewvehicle.php?id=52284

                      http://freepatriot.org

                      Comment


                      • #26
                        Originally posted by Boost Addict View Post
                        I have a set of Hooker headers I'm looking to sell
                        How much? Also how much use iss on them? Feel free to private MSG me
                        GO BLUE
                        sigpic

                        Comment


                        • #27
                          Originally posted by OneMeanFormula View Post
                          Anything as far as money??

                          Sent from my Pantech Breakout using Tapatalk
                          PM me.
                          Originally posted by Yoshi94
                          Mines about an inch bigger than Kyles. I need to get one of those
                          Originally posted by ryanwarby01
                          Put it this way, if you have a money tree a LT1 is a wood chipper!
                          sigpic

                          Comment


                          • #28
                            any good sites to go on to look for the headers/ 3.73 gear?
                            GO BLUE
                            sigpic

                            Comment

                            Working...
                            X