Announcement

Collapse
No announcement yet.

01SS - Restored Project underway!

Collapse
X
Collapse
Who has read this thread:
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Originally posted by kammi10 View Post
    yeah seriously what the ****... post them up
    I had a pic, but deleted it... Nice looking truck, you'll approve of the color.. That's all I got to say about that..
    sigpic
    U.S. Army 1983-2005
    11.20@122.37 1.51 60'

    Originally posted by WMCCjames

    "Plans Subject to change upon Sobering up"

    Comment


    • Originally posted by OIF1VET View Post
      I had a pic, but deleted it... Nice looking truck, you'll approve of the color.. That's all I got to say about that..
      Fay Yull




      Comment


      • Originally posted by kammi10 View Post
        Fay Yull
        Isn't this thread full of that? Lol
        sigpic
        U.S. Army 1983-2005
        11.20@122.37 1.51 60'

        Originally posted by WMCCjames

        "Plans Subject to change upon Sobering up"

        Comment


        • Originally posted by 1BADAIR View Post
          should plug right in. if not there is a little tab to cut .
          smc has them. auburn hills
          I'll be over their way tomorrow....I'll stop by. Thanks....
          sigpic
          o·vr·kill [oh-ver-kil]1. an excess of what is required or suitable, as because of zeal or misjudgment.

          Comment


          • Its bling'd out
            2000 Trans Am l 1967 Firebird

            sigpic

            Comment


            • Ok...more of the little crap no one cares about but I'm celebrating the small victories lately so bare with me. Huge milestone as now this engine is FINALLY ready to go in the hole now that everything in the back of it is complete. Been fighting the little shit but it had to be correct in all aspects of function and appearance.

              Continuing yesterday's issue with the harness was resolved...picked one up today. Everything worked out perfectly from there....



              Map sensor was fun to position and make sure was "serviceable" just in case. So I came up with this. Found a clip that attached to a 3/8-ish line and bonded it to an LS1 sensor. If it were to fail for some reason, simply reach back to unclip and replace





              Routed the line from the valley cover to my vacuum block (hose lying on passenger side valve cover) now clamped to my water line from my water vapor block (hose lying on driver side valve cover) that will finish at the radiator.....naturally a billet clamp




              Oh and for the "race car" guys....the headers fit

              sigpic
              o·vr·kill [oh-ver-kil]1. an excess of what is required or suitable, as because of zeal or misjudgment.

              Comment


              • Don't hide that wire too much. Since you use the extension you will probably have to swap the two outer wires in the cam adapter harness

                Comment


                • Originally posted by 1BADAIR View Post
                  Don't hide that wire too much. Since you use the extension you will probably have to swap the two outer wires in the cam adapter harness
                  I know what you're talking about and looked at wire color before snapping it all together....extension harness match up with the adapter harness.
                  sigpic
                  o·vr·kill [oh-ver-kil]1. an excess of what is required or suitable, as because of zeal or misjudgment.

                  Comment


                  • Two inch primaries?
                    -Joel
                    1995 Z28 M6 - AI226/234 - autocross ricer
                    1984 Scottsdale K10 - 305/4bbl/4spd


                    WTB List:Midwest Chasis DS Loop

                    Comment


                    • sigpic
                      U.S. Army 1983-2005
                      11.20@122.37 1.51 60'

                      Originally posted by WMCCjames

                      "Plans Subject to change upon Sobering up"

                      Comment


                      • hey? did that engine happen to come on a red stand like the gm perf ls's? if so i need one

                        Comment


                        • Originally posted by JoeliusZ28 View Post
                          Two inch primaries?
                          Probably 1 7/8, thats the biggest ive seen for us so far.
                          1999 Camaro - 6 liters of fury.....

                          Comment


                          • Originally posted by 1BADAIR View Post
                            hey? did that engine happen to come on a red stand like the gm perf ls's? if so i need one
                            Lol, an engine or a red stand

                            Originally posted by JoeliusZ28 View Post
                            Two inch primaries?
                            Yessir!
                            sigpic
                            o·vr·kill [oh-ver-kil]1. an excess of what is required or suitable, as because of zeal or misjudgment.

                            Comment


                            • nah, there are 2 inch and 2 stepped to 2 1/4

                              the stand.

                              Comment


                              • Originally posted by OVRKILL View Post
                                Yessir!
                                What company?
                                1996 Trans Am WS6 - long term project


                                Comment

                                Working...
                                X