Tweet
looking good larry. cant wait to see and hear it again. let me know when its home
-
sigpic
11.84 @ 117 w 1.66 60' (previous na best)
- - 5.3/4L80e/T7875 - -
- Huron Speed Turbo Kit -
1998 Formula
-
is it done yet?!?! Crack what whip!
-Derek-
1999 Pontiac Trans Am Ram Air- Lots of Boltons..
Comment
-
Originally posted by redfbird99 View Postis it done yet?!?! Crack what whip!sigpic
U.S. Army 1983-2005
11.20@122.37 1.51 60'
Originally posted by WMCCjamesComment
-
Love the new whitewalls man!2005 Yamaha R6
1999 Pontiac Trans Am - LS1 - M6 - ITSSLOW - 12.998@109.59 - SOLD
1994 Chevrolet Camaro - 3.4L - M5 - ITSSLWR - 16.558@85.38
2003 Chevrolet Blazer
2001 Yamaha YZ426F
Comment
-
I thought it was a nice touch..Originally posted by ITSSLOW View Post
sigpic
U.S. Army 1983-2005
11.20@122.37 1.51 60'
Originally posted by WMCCjamesComment
-
id be so embarrassed to drive thatsigpic
11.84 @ 117 w 1.66 60' (previous na best)
- - 5.3/4L80e/T7875 - -
- Huron Speed Turbo Kit -
1998 Formula
Comment
-
Oh my god...Gordon would be pissed!
Gone but not forgotten: 1986 Chevrolet Camaro IROC-Z
"You shall ride eternal. Shiny and chrome."Comment
-
Went to the shop last week and Chris was pulling the fenders, so I hung around and helped.. They couldn't get the bottom bolts out, Found out why, I had been using a small floor jack to lift the car enough to get a reg floor jack under it. I didn't realize I was lifting on a body panel joint. We were able to save the Passenger side, we heated it with a heat gun and straightened it out and also straightened the sheetmetal.. Put the fender back on and it aligned perfectly.. Drivers side was worse.. I had broken the bottom of the fender, replaced from GM was $211(should have it tomorrow).. Don't mind all the wiring, that's my mess.. Once the bay gets painted I will be putting all the wiring back in place. He is doing the bay for free which is why I am doing all the other stuff for him.. Here's my fenderless *****.. Below that is the fender I ruined.. He is going to repair it so I have a spare, but hard to say if it will hold.
sigpic
U.S. Army 1983-2005
11.20@122.37 1.51 60'
Originally posted by WMCCjamesComment
-
and that right there is why u need a set of stacked boards to drive up on and then put the regular jack under
Comment
-
Nice job on the fender Larry! Doh!
I always hate putting my car in the air cause how low it sits....it's such a pita.sigpicTurbo Charged LS1/T56
Comment
-
You got that right.. Buying a low profile jack now.. Well getting it for Fathers day...Originally posted by WMCCjames View Postsigpic
U.S. Army 1983-2005
11.20@122.37 1.51 60'
Originally posted by WMCCjamesComment
-
get a set of 2x12's one 24 inches long the other 12 and screw them together.. make a set of them and your fineOriginally posted by OIF1VET View Post
Comment
-
True.. and I have some laying around..Originally posted by kammi10 View Postsigpic
U.S. Army 1983-2005
11.20@122.37 1.51 60'
Originally posted by WMCCjamesComment
-
When something says Do Not place Jack Here, I'd advice you DONT PLACE THE JACK THERE lol!It seems like a logical place because the pinch weld is right there, but it does clearly have it labeled in the fender to not place the jack there lol.-Derek-
1999 Pontiac Trans Am Ram Air- Lots of Boltons..
Comment
-
Originally posted by kammi10 View Post
Yup... That is sorta like what I have. Works great!2002 Z28 Camaro A4
1993 Z28 Camaro M6- SOLD
1999 Z28 Camaro M6- SOLD
2008 Ford Fusion SE - DD
-- MCALUS MOLDED PILLAR PODS, PM ME FOR MORE INFO--
sigpicComment
Comment