Tweet
I am going to offer some critical mass stuff here before it goes on the site. They have a strict MAP policy so I can't show you the prices here, but you can email and get them, some things will be over 50% off and all have free shipping. These are true high end products, and for the racers a 12 inch sub weighing just 18 lbs (and rated number one with the highest test scores ever in Car Audio and Electronics mag)
UL12
Product Information
Technical Specifications:
Subwoofer Size: 12”
RMS Power handling: 2500 Watts (undistorted power)
Peak Power handling: 5000 Watts
Recommended Box Volume: 1.2 cuft. (Sealed)
Weight: 16.6 lbs
Motor Type: Dual Gap / Internal NEO Magnet
Voice Coil Type: Ultra-High Temp Dual Coil (Made in the USA)
Voice Coil Diameter: 3”
Voice Coil Impedance: 1.5 ohm nominal per coil
Xmax (one-way linear excursion): 36 mm (3” peak-to-peak)
Maximum Excursion (one way): 46 mm (Almost 4” peak-to-peak)
Sensitivity: 96.7 db (2.83V / 1m) (coils in parallel)
Fs (Klipple-LSI): 31 Hz
Qts (Klipple-LSI): 0.81
Vas (Klipple-LSI): 47.7 Liters
ULTRA-PERFORMANCE LIGHTWEIGHT SUBWOOFER DESIGN:
This driver is the first Ultra-Performance Subwoofer to be made with the automotive
performance enthusiast in mind. At only 18 lbs, this subwoofer handles up-to 3
times more power, has a considerably higher linear and maximum excursion, and
audibly lower distortion, while weighing as much as 66% less than other Ultra-Performance
Subwoofer (woofers with an excursion capability of greater than 2.5”).
These subwoofers made by other companies can weigh as much as 55 lbs. On the
other hand, the Critical MASS Ultra-Performance Lightweight Subwoofer will not
only play louder and handle more power, but it will also play in a smaller box, and
therefore, can save you as much as 100 lbs from subwoofer system weight when
combined with the reduced weight of a smaller enclosure (based on two 12” subs).
A 100 lbs reduction in your system weight, translates to accelerations gains resulting
in up to 1/10th of a second off your 0-60 mph times, or as much as 1 car length
faster. So the next time you plan to invest $1000 on an exhaust system, keep in mind
that you may have already lost your expected performance gains, unless you are using
Critical MASS UL-Series subwoofers and speakers.
MMAG TECHNOLOGY:
Allows for much greater linear excursion and power handling than conventional
drivers. This Ultra-Performance Subwoofer utilizes the Dual Gap configuration of
the patented MMAG motor technology, which results in up to 2.5 times more X-max
than conventional motor designs.
Huge, radial slot vented, NEO motor structure. Utilizing the latest and best high temp,
high grade Neodymium-Iron-Born magnets, which generate up-to 20 times more magnetic energy
than conventional ceramic magnets of equivalent size. The radial slot vents keep the
motor running cool, enabling much greater power handling capability than conventional
Neo designs.
OSD TECHNOLOGY:
Up to 25% more air movement do to Oversized Sd technology as compared to other
drivers with comparable excursion capability. Combined with the X-max improvements
of the Dual Gap geometry, this subwoofer delivers over 200% more linear air
movement (more Bass) than conventional subwoofers with the same size voice coil.
HEAT-SINK BASKET TECHNOLOGY:
Utilizing a unique and efficient way of transferring heat, from the motor, to the basket
body, and then to the basket mounting flange. This Ultra-Performance Subwoofer
actually transfers the heat from inside the Box to the outside world by utilizing its
heat-sink fins on the face of the woofer’s mounting flange. Not only does this technology
allow for increased short-term power handling, but also for greater power
handling over long periods of time (many more hours than conventional designs).
CARBON FIBER SANDWICH CONE:
This cone is one of the only cones that will withstand 5000 Watts of peak music
power. The Lightweight Carbon Fiber Sandwich Cone increases rigidity, and therefore
efficiency, which ultimately means more, undistorted, car-shaking bass.
list price $1999
C652
6.5in components
TECHNICAL INFORMATION:
Max Power Handling : 400 W
RMS Power Handling : 200 W
X-Over Type : 24 db/oct
Speaker Size : 6.5"
Voice Coil : 2.25"
Fs : 39 Hz
db@1W/1M : 93 db
Motor : NEO
FEATURES :
Thin Mount Design:
Allows for custom shallow depth Installations.
Lightweight Design:
Weighs up to 66% less than most other High Power Speakers.
Huge NEO Motor structure:
Up to 20 times more magnetic charge than standard magnets.
Huge 2.25" Multi Layer Voice Coil:
More than 3 times the power-handling of other shallow Depth Speakers.
Inverted Motor structure:
Further increases long term power handling and allows for shallow mounting depth.
Woven Carbon/Glass Fiber Cone:
Increased Power to Weight ratio.
24 db/oct Professional Grade X-overs:
Allows for absolute clarity at all power levels.
Bi-Ampable X-overs:
Allows the tweeter and woofer to be powered by separate amplifiers.
30mm Soft-dome tweeters:
Huge tweeter voice coil for truer sound.
List price $704
SS6
6.5in coax speakers
Product Information
6.5" Coaxial with 25mm Soft Dome
RMS : 75
V. C. : 1"
Motor : STRD
X-over : 12 db/oct
F3hz : TBA
db/2.83V : 91
Ohm : 4
Qft min : TBA
list $189
SS69
6x9 coax speakers
Product Information
6x9" Coaxial with 25mm Soft Dome
RMS : 100
V. C. : 1"
Motor : STRD
X-over : 12 db/oct
F3hz : TBA
db/2.83V : 91
Ohm : 4
Qft min : TBA
List $199
SS-A400
75wx4 amp
Product Information
FEATURES:
* High pass variable crossover (40 Hz~240Hz at 12 dB/OCT – 1,2,3,4CH
* Low pass variable crossover (40Hz~240Hz at 12dB/OCT – 1,2,3,4CH
* Full range switch for 1,2,3,4CH
* Power on L.E.D.
* Protection indicator L.E.D.
* Sub sonic filter 15~30Hz
* Sub sonic functions ON - OFF
* Gain volume Min - Max
* Protection circuit for thermal, overload, DC reverse, DV offset
* Remocon for subwoofer
SPECIFICATIONS:
* Frequency response 15Hz~230Hz
* RMS power at 4OHM Stereo 75W x 4CH
* RMS Power at 4OHM Mono (Bridged) 200W x 2CH
* RMS Power at 2OHM Stereo 100W x 4CH
* Max power 600W @ 14.4V
* T.H.D. 0.05%
* Input sensitivity 200mV~4V
* Input impedance 20K ohms
* Damping factor >500
* S/N Ratio 105 db
* Channel separation 90dB
List $1299
UL-A2500
1300 watt mono amp
Product Information
FEATURES:
* Mono block digital subwoofer amplifier
* Remote bass boost at 60Hz control: 0-18dB
* Balanced low input & high input
* Line out ( by pass)
* Variable subsonic filter 15~30Hz, 18dB/OCT
* Variable low pass filter 40~230Hz, 24dB/OCT
* Variable bass boost at 60Hz control: 0-18dB
* Phase control 0º~180º
* Protection circuit for thermal, short circuit and reverse polarity connection of Battery
SPECIFICATIONS:
* Frequency response 15Hz~250Hz
* RMS power at 4OHM mono 1300 W
* RMS power at 2OHM mono 1900 W
* RMS power at 1OHM mono 2500 W
* Max power 5000W @14.4V
* T.H.D 0.01%
* Input sensitivity 200mV~7V
* Input impedance 20K ohms
* Damping factor >500
* S/N ratio 105dB
list $2495
And a standard 12 for those needing something a bit cheaper
SS122
Product Information
12" Long-Throw High Power Subwoofer
RMS : 500
V. C. : 2"
Motor : STRD
X-over : N/A
F3hz : 26hz
db/2.83V : 90
Ohm : 2
Qft min : TBA
List $189
check out their site
http://www.criticalmassaudio.com/ and yes we can do the electrostats but we get your car for 60 days and it costs over $200,000 to do it
UL12
Product Information
Technical Specifications:
Subwoofer Size: 12”
RMS Power handling: 2500 Watts (undistorted power)
Peak Power handling: 5000 Watts
Recommended Box Volume: 1.2 cuft. (Sealed)
Weight: 16.6 lbs
Motor Type: Dual Gap / Internal NEO Magnet
Voice Coil Type: Ultra-High Temp Dual Coil (Made in the USA)
Voice Coil Diameter: 3”
Voice Coil Impedance: 1.5 ohm nominal per coil
Xmax (one-way linear excursion): 36 mm (3” peak-to-peak)
Maximum Excursion (one way): 46 mm (Almost 4” peak-to-peak)
Sensitivity: 96.7 db (2.83V / 1m) (coils in parallel)
Fs (Klipple-LSI): 31 Hz
Qts (Klipple-LSI): 0.81
Vas (Klipple-LSI): 47.7 Liters
ULTRA-PERFORMANCE LIGHTWEIGHT SUBWOOFER DESIGN:
This driver is the first Ultra-Performance Subwoofer to be made with the automotive
performance enthusiast in mind. At only 18 lbs, this subwoofer handles up-to 3
times more power, has a considerably higher linear and maximum excursion, and
audibly lower distortion, while weighing as much as 66% less than other Ultra-Performance
Subwoofer (woofers with an excursion capability of greater than 2.5”).
These subwoofers made by other companies can weigh as much as 55 lbs. On the
other hand, the Critical MASS Ultra-Performance Lightweight Subwoofer will not
only play louder and handle more power, but it will also play in a smaller box, and
therefore, can save you as much as 100 lbs from subwoofer system weight when
combined with the reduced weight of a smaller enclosure (based on two 12” subs).
A 100 lbs reduction in your system weight, translates to accelerations gains resulting
in up to 1/10th of a second off your 0-60 mph times, or as much as 1 car length
faster. So the next time you plan to invest $1000 on an exhaust system, keep in mind
that you may have already lost your expected performance gains, unless you are using
Critical MASS UL-Series subwoofers and speakers.
MMAG TECHNOLOGY:
Allows for much greater linear excursion and power handling than conventional
drivers. This Ultra-Performance Subwoofer utilizes the Dual Gap configuration of
the patented MMAG motor technology, which results in up to 2.5 times more X-max
than conventional motor designs.
Huge, radial slot vented, NEO motor structure. Utilizing the latest and best high temp,
high grade Neodymium-Iron-Born magnets, which generate up-to 20 times more magnetic energy
than conventional ceramic magnets of equivalent size. The radial slot vents keep the
motor running cool, enabling much greater power handling capability than conventional
Neo designs.
OSD TECHNOLOGY:
Up to 25% more air movement do to Oversized Sd technology as compared to other
drivers with comparable excursion capability. Combined with the X-max improvements
of the Dual Gap geometry, this subwoofer delivers over 200% more linear air
movement (more Bass) than conventional subwoofers with the same size voice coil.
HEAT-SINK BASKET TECHNOLOGY:
Utilizing a unique and efficient way of transferring heat, from the motor, to the basket
body, and then to the basket mounting flange. This Ultra-Performance Subwoofer
actually transfers the heat from inside the Box to the outside world by utilizing its
heat-sink fins on the face of the woofer’s mounting flange. Not only does this technology
allow for increased short-term power handling, but also for greater power
handling over long periods of time (many more hours than conventional designs).
CARBON FIBER SANDWICH CONE:
This cone is one of the only cones that will withstand 5000 Watts of peak music
power. The Lightweight Carbon Fiber Sandwich Cone increases rigidity, and therefore
efficiency, which ultimately means more, undistorted, car-shaking bass.
list price $1999
C652
6.5in components
TECHNICAL INFORMATION:
Max Power Handling : 400 W
RMS Power Handling : 200 W
X-Over Type : 24 db/oct
Speaker Size : 6.5"
Voice Coil : 2.25"
Fs : 39 Hz
db@1W/1M : 93 db
Motor : NEO
FEATURES :
Thin Mount Design:
Allows for custom shallow depth Installations.
Lightweight Design:
Weighs up to 66% less than most other High Power Speakers.
Huge NEO Motor structure:
Up to 20 times more magnetic charge than standard magnets.
Huge 2.25" Multi Layer Voice Coil:
More than 3 times the power-handling of other shallow Depth Speakers.
Inverted Motor structure:
Further increases long term power handling and allows for shallow mounting depth.
Woven Carbon/Glass Fiber Cone:
Increased Power to Weight ratio.
24 db/oct Professional Grade X-overs:
Allows for absolute clarity at all power levels.
Bi-Ampable X-overs:
Allows the tweeter and woofer to be powered by separate amplifiers.
30mm Soft-dome tweeters:
Huge tweeter voice coil for truer sound.
List price $704
SS6
6.5in coax speakers
Product Information
6.5" Coaxial with 25mm Soft Dome
RMS : 75
V. C. : 1"
Motor : STRD
X-over : 12 db/oct
F3hz : TBA
db/2.83V : 91
Ohm : 4
Qft min : TBA
list $189
SS69
6x9 coax speakers
Product Information
6x9" Coaxial with 25mm Soft Dome
RMS : 100
V. C. : 1"
Motor : STRD
X-over : 12 db/oct
F3hz : TBA
db/2.83V : 91
Ohm : 4
Qft min : TBA
List $199
SS-A400
75wx4 amp
Product Information
FEATURES:
* High pass variable crossover (40 Hz~240Hz at 12 dB/OCT – 1,2,3,4CH
* Low pass variable crossover (40Hz~240Hz at 12dB/OCT – 1,2,3,4CH
* Full range switch for 1,2,3,4CH
* Power on L.E.D.
* Protection indicator L.E.D.
* Sub sonic filter 15~30Hz
* Sub sonic functions ON - OFF
* Gain volume Min - Max
* Protection circuit for thermal, overload, DC reverse, DV offset
* Remocon for subwoofer
SPECIFICATIONS:
* Frequency response 15Hz~230Hz
* RMS power at 4OHM Stereo 75W x 4CH
* RMS Power at 4OHM Mono (Bridged) 200W x 2CH
* RMS Power at 2OHM Stereo 100W x 4CH
* Max power 600W @ 14.4V
* T.H.D. 0.05%
* Input sensitivity 200mV~4V
* Input impedance 20K ohms
* Damping factor >500
* S/N Ratio 105 db
* Channel separation 90dB
List $1299
UL-A2500
1300 watt mono amp
Product Information
FEATURES:
* Mono block digital subwoofer amplifier
* Remote bass boost at 60Hz control: 0-18dB
* Balanced low input & high input
* Line out ( by pass)
* Variable subsonic filter 15~30Hz, 18dB/OCT
* Variable low pass filter 40~230Hz, 24dB/OCT
* Variable bass boost at 60Hz control: 0-18dB
* Phase control 0º~180º
* Protection circuit for thermal, short circuit and reverse polarity connection of Battery
SPECIFICATIONS:
* Frequency response 15Hz~250Hz
* RMS power at 4OHM mono 1300 W
* RMS power at 2OHM mono 1900 W
* RMS power at 1OHM mono 2500 W
* Max power 5000W @14.4V
* T.H.D 0.01%
* Input sensitivity 200mV~7V
* Input impedance 20K ohms
* Damping factor >500
* S/N ratio 105dB
list $2495
And a standard 12 for those needing something a bit cheaper
SS122
Product Information
12" Long-Throw High Power Subwoofer
RMS : 500
V. C. : 2"
Motor : STRD
X-over : N/A
F3hz : 26hz
db/2.83V : 90
Ohm : 2
Qft min : TBA
List $189
check out their site
http://www.criticalmassaudio.com/ and yes we can do the electrostats but we get your car for 60 days and it costs over $200,000 to do it
Comment