Tweet
Top half of an LS7 engine, very low miles, ready to go heads, rockers, intake. Also have Aeromotive Billet Fuel rails for this, brand new in box. $2000obo for everything.
Weldon 2025 pump, used, works great. Excellent pump for 1200hp street cars. Was saving this but the car I bought already had one. $300
Mini-3g alternator for Ford. This is a high output unit that will bolt on to a Fox mustang but is smaller in size than the 3g. This has very little use on it, will sell for half of whatever they cost.
FOX Mustang hood hinges, hood latch, 2 pieces of belt line molding, $20obo just don't want to throw it away.
Severely lightened front bumper and mounts for FOX Mustang, mounts are aluminum copies of the factory mount. This stuff weighs nothing and offers no protection, but will keep the fascia from buckling at speed, $25
Old off-brand speakers installed in crudely cut out wood. These will fit in the size the 79-86 Mustang rear speaker areas were. Perfect for building a "period correct" 1980's era teenager's car. $400 very firm.
Global West caster plates for FOX Mustang, old school but work great, $25
Box which appears to have a brand new Dynomax Diesel truck chrome exhaust tip, 87-89 Mustang steering wheel, plug wires, recall tach that has an intermittent problem, 2006 F150 Door handle, misc SBF plug wires, SBF Pushrods, 4 lug FOX Mustang 5/16th wheel spacers, etc will trade for cold 6 pack of bud light.
Box which appears to contain early FOX speedometer cable, clutch cable, shifter bezel, prindel, etc, will trade for cold 6 pack of bud light.
(2) Weld Draglite wheels, 15x10, 4.5" backspacing, 5x4.5" bolt pattern, with well worn 325 drag radials on them. These fit nice on mini-tubbed Mustangs, $200obo
Full set of Weld Draglites, powder coated "black chrome (grey)" by QC Coatings, rears are 15x12" with 6.5" backspacing, fronts are 15x3.5. Rears have Hoosier 29.5x10.5w slicks, fronts have no tires on them. Rim screws installed by Harlow or Mcormick, Rear slicks are almost new, ONE pass on them. Stored in basement, $600 obo or trade.
Pics of everything here:
http://www.detroitracing.com/forums/...ad.php?t=10537
Weldon 2025 pump, used, works great. Excellent pump for 1200hp street cars. Was saving this but the car I bought already had one. $300
Mini-3g alternator for Ford. This is a high output unit that will bolt on to a Fox mustang but is smaller in size than the 3g. This has very little use on it, will sell for half of whatever they cost.
FOX Mustang hood hinges, hood latch, 2 pieces of belt line molding, $20obo just don't want to throw it away.
Severely lightened front bumper and mounts for FOX Mustang, mounts are aluminum copies of the factory mount. This stuff weighs nothing and offers no protection, but will keep the fascia from buckling at speed, $25
Old off-brand speakers installed in crudely cut out wood. These will fit in the size the 79-86 Mustang rear speaker areas were. Perfect for building a "period correct" 1980's era teenager's car. $400 very firm.
Global West caster plates for FOX Mustang, old school but work great, $25
Box which appears to have a brand new Dynomax Diesel truck chrome exhaust tip, 87-89 Mustang steering wheel, plug wires, recall tach that has an intermittent problem, 2006 F150 Door handle, misc SBF plug wires, SBF Pushrods, 4 lug FOX Mustang 5/16th wheel spacers, etc will trade for cold 6 pack of bud light.
Box which appears to contain early FOX speedometer cable, clutch cable, shifter bezel, prindel, etc, will trade for cold 6 pack of bud light.
(2) Weld Draglite wheels, 15x10, 4.5" backspacing, 5x4.5" bolt pattern, with well worn 325 drag radials on them. These fit nice on mini-tubbed Mustangs, $200obo
Full set of Weld Draglites, powder coated "black chrome (grey)" by QC Coatings, rears are 15x12" with 6.5" backspacing, fronts are 15x3.5. Rears have Hoosier 29.5x10.5w slicks, fronts have no tires on them. Rim screws installed by Harlow or Mcormick, Rear slicks are almost new, ONE pass on them. Stored in basement, $600 obo or trade.
Pics of everything here:
http://www.detroitracing.com/forums/...ad.php?t=10537
Comment