Tweet
Yes you are reading that right! Full 1 7/8" Longtubes to Tip systems shipped to your door for $850!!!! To make this even better, if you get in on the first 20 order, I will put your name down in this thread and once I have all 20, I will randomly draw one person to win all of their money back!!!!!! $850 You MIFbody guys will of course get put in the Camaro5 raffle as well! I have been over on the CorvetteForum and have been offered a product to bring to the new 2010+ Camaro market!
Full exhaust for the 2010+ Camaro SS :w00t:
Info on the system:
-1 7/8" Primary longtube headers
-Made out of 321 Stainless Steel polished to a chrome like finish!
-3" X-pipe and intermediate pipes
-Offroad version
-3" Catback with mufflers and tips
-All gaskets, bolts, clamps are included!
-Only item needed to complete the install is (2) 6" O2 extensions.
INTRO Pricing for the first 25 orders ONLY and then pricing will move up so get them while they are smokin'!!!!! If you order, the first 20 people will get their name signed down below and one of them will be chosen at random to win all of their $850 BACK! Simply add in your Camaro5 username and phone number to the description when checking out and you will be added to the list!
Complete system from headers to tips: $850
Headers only: $475
Complete catback exhaust: $525
**All pricing INCLUDES Shipping in the lower 48**
Visit here to order:
http://oversteeringonline.com/2010__Camaro_Exhaust.html
HEAR IT!
Basic run down on the install:
INSTRUCTIONS
1. Remove engine cover, plug wires,and plugs.
2. Remove left and right head pipe nuts.
3. Unplug O2 sensor on left and right. Be careful not to break these so you can reuse them.
4. Remove left exhaust manifold bolts, and take left side manifold up through the top.
5. Remove dip stick tube and save.
6. Remove right side manifold bolts.
7. Raise car, unplug and remove rear O2 sensors. SAVE.
8. Loosen band clamps, remove "cats".
9. Once you remove right side cat, the exhaust manifold can come out bottom.
10. Remove drive shaft hoop.
11. Remove rubber hangers and exhaust will come out in one piece.
12. Install right and left side headers EXTRA HANDS WILL BE NEEDED FOR THIS STEP! Install from the BOTTOM!
13. Slide clamps onto "x-pipe".
14. Install x-pipe with the "hump" on the top side. ( make sure x-pipe is in center of tunnel before tightening!)
15. Slide clamps onto rear x-pipe.
16. Slide clamps onto intermediate pipe.
17. Install mufflers.
18. Snug everything finger tight.
19. Tighten all clamps, flanges and hangers, FROM FRONT TO BACK.
20. Make sure that exhaust tips are centered in holes of rear valence.
21. Tighten rear hangers.
22. Reinstall rear O2 sensors. (harness is long enough).
23. You will need 6" extensions for both front O2 sensors.
Intro Pricing Spots Open: 24
First 20 orders $850 cash back raffle!
1.)
2.)
3.)
4.)
5.)
6.)
7.)
8.)
9.)
10.)
11.)
12.)
13.)
14.)
15.)
16.)
17.)
18.)
19.)
20.)
Full exhaust for the 2010+ Camaro SS :w00t:
Info on the system:
-1 7/8" Primary longtube headers
-Made out of 321 Stainless Steel polished to a chrome like finish!
-3" X-pipe and intermediate pipes
-Offroad version
-3" Catback with mufflers and tips
-All gaskets, bolts, clamps are included!
-Only item needed to complete the install is (2) 6" O2 extensions.
INTRO Pricing for the first 25 orders ONLY and then pricing will move up so get them while they are smokin'!!!!! If you order, the first 20 people will get their name signed down below and one of them will be chosen at random to win all of their $850 BACK! Simply add in your Camaro5 username and phone number to the description when checking out and you will be added to the list!
Complete system from headers to tips: $850
Headers only: $475
Complete catback exhaust: $525
**All pricing INCLUDES Shipping in the lower 48**
Visit here to order:
http://oversteeringonline.com/2010__Camaro_Exhaust.html
HEAR IT!
Basic run down on the install:
INSTRUCTIONS
1. Remove engine cover, plug wires,and plugs.
2. Remove left and right head pipe nuts.
3. Unplug O2 sensor on left and right. Be careful not to break these so you can reuse them.
4. Remove left exhaust manifold bolts, and take left side manifold up through the top.
5. Remove dip stick tube and save.
6. Remove right side manifold bolts.
7. Raise car, unplug and remove rear O2 sensors. SAVE.
8. Loosen band clamps, remove "cats".
9. Once you remove right side cat, the exhaust manifold can come out bottom.
10. Remove drive shaft hoop.
11. Remove rubber hangers and exhaust will come out in one piece.
12. Install right and left side headers EXTRA HANDS WILL BE NEEDED FOR THIS STEP! Install from the BOTTOM!
13. Slide clamps onto "x-pipe".
14. Install x-pipe with the "hump" on the top side. ( make sure x-pipe is in center of tunnel before tightening!)
15. Slide clamps onto rear x-pipe.
16. Slide clamps onto intermediate pipe.
17. Install mufflers.
18. Snug everything finger tight.
19. Tighten all clamps, flanges and hangers, FROM FRONT TO BACK.
20. Make sure that exhaust tips are centered in holes of rear valence.
21. Tighten rear hangers.
22. Reinstall rear O2 sensors. (harness is long enough).
23. You will need 6" extensions for both front O2 sensors.
Intro Pricing Spots Open: 24
First 20 orders $850 cash back raffle!
1.)
2.)
3.)
4.)
5.)
6.)
7.)
8.)
9.)
10.)
11.)
12.)
13.)
14.)
15.)
16.)
17.)
18.)
19.)
20.)
...well, that, and he'd probably hire somebody to put it on for him...which may create an issue...)
Comment