Lots of trans am stuff, exhaust/driveline

Ive got for sale a lot of parts coming out of my trans am as its now pretty much going to be for race use only. with that being said. This is all up for sale. pricing will be best offer. Lowballs will not even be responded to. All parts are located in metro detroit and I will meet people a reasonable distance if need be for the price of gas.

1. 10 bolt rear axle with 3.42 gears. Low mileage and new gears. Axle itself has 30k on it. Gears have 5k. The guy before me thought he paid a shop to install 4.10s and didnt realize they put in another set of 3.42's...dumb
Anyhow, it works perfectly fine, no sounds, and the posi is tight. it is also very clean inside and out. 300 obo

2. LS1 Aluminum driveshaft...100 or best offer, currently has conversion ujoint on back for ford 9-inch. would have to be swapped for standard fbod ujoint for 10bolt if needed.

3. stock torque arm, 50 or best offer

4. Hooker catback. this is only the part that goes over the axle to the exhaust tips. the rest of the exhaust contains a electric cutout that the motor died on, i will throw it in for a few bucks as it could be rebuilt and installed on the cutouts y-pipe, 150 or best offer

5. T56 6 speed with hurst billet plus shifter. 30k original miles, fluid changed religiously. clutch available seperately. make an offer

6. Mcleod Street Twin, only 2500 break in miles on it. Decided that an automatic would be better suited for what i want to do with the car. This is retailing for 1450 right now. Also comes with Billet Steel flywheel and adjustable master cylinder. best offer
__________________

[Hugger Z]

What are you doing now...... Man you just can't leave that car alone can you?

If I wasn't worried about the torque on my driveshaft I might be interested in that one when I get an upgraded rear next year. But I will have to pass as I think I need to get a steel one and a safety loop! Good luck man and let me know if you need any help pulling stuff off the car.

[Formula Z]

man that would be a cool winter project making my A4 an M6...................

[Derek]

i am interested in the rear, i need this for my car, have you confirmed they are 3.42s and a 3channel with ABS? and would you take 250? that seems to be the going rate for rear ends.. I bought one last fall for that and it was a 4 channel not 3 channel that I need

[cjmatt]

i am interested in the rear, i need this for my car, have you confirmed they are 3.42s and a 3channel with ABS? and would you take 250? that seems to be the going rate for rear ends.. I bought one last fall for that and it was a 4 channel not 3 channel that I need

yes, every trans am with a 6 speed has always had 3.42s and 4 channel abs wasnt available on 94 models. This car doesnt have traction control either fyi

[1BADAIR]

man that would be a cool winter project making my A4 an M6...................

note that lt1 and ls1 T56's have differant input shafts

[scholtmj]

Still got that tranny?

[alwaysmessedup]

do you still have the driveshaft and what will you take, seriously interested.

[ConfusedGarage]

Going auto...if there was only a giant vagina smiley!!!! JK.

Tony you need one of those 3.5 pst driveshafts from EPP. They are warranted against carnage for life.

[my1994z28]

Do u still have the trans?

[96BlackBetty]

got any pics of that exhaust?

[00firebird]

what year rear end, and is it TCS & ABS?