Tweet
right now looks like im left with no other choice but to either sell the car or part it out for money.
ive had people ask what i want for the engine and i told them its what im asking for the car so your better off just buying the car.
The cars a 93 firebird full race suspension minus front suspension from a v6 car was a v6 before i changed it over.
rear has airbags not installed yet. has Offset Mad Max Racing LCA's, BMR Track pak, BMR sbc/bbc tubular K member, BMR boxed sfc,.
vehicle has been tubbed but needs the Wolfe racing Wheel tub kit welded in. I have the kit int he car. the vehicle needs to be rewired, just lights and switches.
the vehicle is close to completion but i ran out of money and time to finish it. it needs one fitting to complete the nitrous install it has a 250 kit installed on it. with a 1 inch plate, carb is a holley 750 dp race set. heads have been milled .06 to give a compression of 11.5:1. there are fuel pumps two regulators installed on the vehicle one for nitrous one for motor. the engines a gen 1 SBC 357 its bored .042 over with fully forged internals the cam is 244 252 57x 59x i have to look up the specs its on a 110 lsa. its a solid cam. this engines been made to hold the power presented through it. the trans is a th350 race built. with a 3600 10" stall converter the rear axle is a moser 9 inch with 35 spline axles a spool and 4.57 gears built by Scott K. the car has a 10 pt cage installed, engine fits under the hood. the ignition is all MSD. alot of you have seen the car the last time i had it out and running. ive dumped alot of money in this car id ont like to tell people how much is spent but its well over 30 grand.
Im offering this for 8000 obo or ill part this vehicle out. ive offered the rear end but he hasnt gotten back to me yet.
any questions Message me on here or email me at wasjo6431@yahoo.com
ive had people ask what i want for the engine and i told them its what im asking for the car so your better off just buying the car.
The cars a 93 firebird full race suspension minus front suspension from a v6 car was a v6 before i changed it over.
rear has airbags not installed yet. has Offset Mad Max Racing LCA's, BMR Track pak, BMR sbc/bbc tubular K member, BMR boxed sfc,.
vehicle has been tubbed but needs the Wolfe racing Wheel tub kit welded in. I have the kit int he car. the vehicle needs to be rewired, just lights and switches.
the vehicle is close to completion but i ran out of money and time to finish it. it needs one fitting to complete the nitrous install it has a 250 kit installed on it. with a 1 inch plate, carb is a holley 750 dp race set. heads have been milled .06 to give a compression of 11.5:1. there are fuel pumps two regulators installed on the vehicle one for nitrous one for motor. the engines a gen 1 SBC 357 its bored .042 over with fully forged internals the cam is 244 252 57x 59x i have to look up the specs its on a 110 lsa. its a solid cam. this engines been made to hold the power presented through it. the trans is a th350 race built. with a 3600 10" stall converter the rear axle is a moser 9 inch with 35 spline axles a spool and 4.57 gears built by Scott K. the car has a 10 pt cage installed, engine fits under the hood. the ignition is all MSD. alot of you have seen the car the last time i had it out and running. ive dumped alot of money in this car id ont like to tell people how much is spent but its well over 30 grand.
Im offering this for 8000 obo or ill part this vehicle out. ive offered the rear end but he hasnt gotten back to me yet.
any questions Message me on here or email me at wasjo6431@yahoo.com
357ci LT1, cammed, stalled, and driven. 
Comment