School me on nitrous

[MunsterZ28]

Im not expert on the subject, but I do know that if you want to do it right and safe you can expect to spend a bare minimun of $1000

if you buy everything brand new, i got my kit off clist and the rest of it off tech for right around $400.

[ThreeHonks]

what saftey equipment are you running? Do you have any electronic controllers? bottle heater? Do you have an ignition box to pull timing, etc.?


If its done RIGHT, its not cheap

[MunsterZ28]

what saftey equipment are you running? Do you have any electronic controllers? bottle heater? Do you have an ignition box to pull timing, etc.?


If its done RIGHT, its not cheap

yes i have have a wide open throttle and window switch. an edelbrock bottle heater and no im not pulling timing for a 75 shot that ive used twice

[kyleozzie]

last year i got a kit really cheap, ended up running a 100 shot on a WOT i wasnt using a window switch, nor any way to pull timing.. was rebuilding so i didnt care, but you need at bare min. a window switch forsure.. this year i plan on getting a mallory 685 box so i can pull timing, and it includes a built in window switch.. there pretty cheap too!

[JSTALT1]

I wanna put a 100 shot on my car, dont know how much the motor would handle tho. I have a mallory 685 box sitting in the garage when i do tho

[MunsterZ28]

I wanna put a 100 shot on my car, dont know how much the motor would handle tho. I have a mallory 685 box sitting in the garage when i do tho

my lt1 has a 135,000 miles on it and has handled a 125 shot 3 times so far lol. if thats anything to you.

[JSTALT1]

no that definately means something to me, good to hear that its holding up, I just wanna make sure mine stays reliable. but what fun is reliable

[Detoxx03]

I gave Futral Motorsports a deposit yesterday for my setup. I will be spraying a 150 shot and my setup will consist of a 92mm wet plat kit, window switch, msd timing twister, fuel pump, bigger injectors, new plugs, bottle heater, pressure gauge, fpss, blow down fitting and tube, purge valve, opener, switch panel, and some other stuff i'm forgetting.

When it comes to my car I want to be safe and reliable so i'll spend money to make sure its right so imo a good setup is not cheap.

[Darren]

I gave Futral Motorsports a deposit yesterday for my setup. I will be spraying a 150 shot and my setup will consist of a 92mm wet plat kit, window switch, msd timing twister, fuel pump, bigger injectors, new plugs, bottle heater, pressure gauge, fpss, blow down fitting and tube, purge valve, opener, switch panel, and some other stuff i'm forgetting.

When it comes to my car I want to be safe and reliable so i'll spend money to make sure its right so imo a good setup is not cheap.

Your car is going to be a beast at the track with a 150 shot on top of what you already run.

[OIF1VET]

I gave Futral Motorsports a deposit yesterday for my setup. I will be spraying a 150 shot and my setup will consist of a 92mm wet plat kit, window switch, msd timing twister, fuel pump, bigger injectors, new plugs, bottle heater, pressure gauge, fpss, blow down fitting and tube, purge valve, opener, switch panel, and some other stuff i'm forgetting.

When it comes to my car I want to be safe and reliable so i'll spend money to make sure its right so imo a good setup is not cheap.

Sweet dude! 10's shouldn't be a problem!

[Detoxx03]

Your car is going to be a beast at the track with a 150 shot on top of what you already run.

I'm very excited

Sweet dude! 10's shouldn't be a problem!

I'm scared for my rear end now lol

[OIF1VET]

I'm very excited



I'm scared for my rear end now lol

I've been scared!

[1BADAIR]

chickens

[Darren]

I'm very excited



I'm scared for my rear end now lol

I've been scared!

As you both should be!

[Detoxx03]

I know i'm gonna change it eventually its just a matter of when