Announcement

Collapse
No announcement yet.

Bent axle? Vid inside

Collapse
X
Collapse
Who has read this thread:
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #16
    Originally posted by Lucky SOB View Post
    might as well replace both while you're doing it right?
    That be the plan. I need to borrow one of Brent's money trees.

    sigpic
    U.S. Army 1983-2005
    11.20@122.37 1.51 60'

    Originally posted by WMCCjames

    "Plans Subject to change upon Sobering up"

    Comment


    • #17
      Wait, he has more than one? Dibs if he has another spare! Haha.

      Well, at least axles arent TOO huge of an ordeal. Obviously theres cost involved, but its not like your ripping the whole car apart to change them.
      1999 Camaro - 6 liters of fury.....

      Comment


      • #18
        Originally posted by sman View Post
        Wait, he has more than one? Dibs if he has another spare! Haha.

        Well, at least axles arent TOO huge of an ordeal. Obviously theres cost involved, but its not like your ripping the whole car apart to change them.
        He has several trees. Yea, at least the rear can stay in. Will get em pulled this week, maybe.
        sigpic
        U.S. Army 1983-2005
        11.20@122.37 1.51 60'

        Originally posted by WMCCjames

        "Plans Subject to change upon Sobering up"

        Comment


        • #19
          when you order them dont forget to have them put the 1/2 inch studs in them now




          Comment


          • #20
            Moser can straighten axles for $ 50... http://www.moserengineering.com/moser/shop-services/
            sigpic

            355 LT1 M6. 232/240 LE cam. 21* Trick Flow heads. Fully ported intake. 58mm TPIS tb. 42# SVO Injectors. LS7 Lifters. Moser 9" TrueTrac w/ 4.22 gears. True Duals. UMI Suspension. LS1 brake swap. Dr. Phil tuned 400ish rwhp. Money Pit.

            Comment


            • #21
              Originally posted by kammi10 View Post
              when you order them dont forget to have them put the 1/2 inch studs in them now
              Yes sir!

              Originally posted by ryanwarby01 View Post
              Moser can straighten axles for $ 50... http://www.moserengineering.com/moser/shop-services/
              Thanks, but no thanks..
              sigpic
              U.S. Army 1983-2005
              11.20@122.37 1.51 60'

              Originally posted by WMCCjames

              "Plans Subject to change upon Sobering up"

              Comment


              • #22
                I would not buy moser axles if you are shopping for new ones
                sigpic
                Turbo Charged LS1/T56

                Comment


                • #23
                  Originally posted by WMCCjames View Post
                  I would not buy moser axles if you are shopping for new ones
                  I was planning on strange..
                  sigpic
                  U.S. Army 1983-2005
                  11.20@122.37 1.51 60'

                  Originally posted by WMCCjames

                  "Plans Subject to change upon Sobering up"

                  Comment


                  • #24
                    How many splines are your axles?

                    I met a guy last week on Woodward that told me he was the first person ever to get a F Body BMR K member and a bunch of other stuff. He said he runs a Moser 12 bolt and it will hold 2500hp and if he could break it Moser said they would buy it back from him. I was like oh yeah considering a 9" and a Dana 60 are stronger and are only rated to ~1500hp.

                    Oh and his engine was stock. He didn't even put heads or a cam in it.
                    Last edited by Fox Slaughter; April 15th, 2012, 12:47 PM.
                    Originally posted by Yoshi94
                    Mines about an inch bigger than Kyles. I need to get one of those
                    Originally posted by ryanwarby01
                    Put it this way, if you have a money tree a LT1 is a wood chipper!
                    sigpic

                    Comment


                    • #25
                      Originally posted by WMCCjames View Post
                      I would not buy moser axles if you are shopping for new ones
                      never once had a problem with mine..




                      Comment


                      • #26
                        Sorry to hear about the problems, Larry. Maybe if the seller doesn't get back to you, you should just toss the bad axle through the front window of his house.
                        When in doubt, Whip it out !

                        Comment


                        • #27
                          Originally posted by farmington View Post
                          Sorry to hear about the problems, Larry. Maybe if the seller doesn't get back to you, you should just toss the bad axle through the front window of his house.
                          He is in Nebraska. Or I would.

                          Originally posted by Fox Slaughter View Post
                          How many splines are your axles?.
                          31 spline.
                          sigpic
                          U.S. Army 1983-2005
                          11.20@122.37 1.51 60'

                          Originally posted by WMCCjames

                          "Plans Subject to change upon Sobering up"

                          Comment


                          • #28
                            Damn Larry that's bad. Looks like this good deal is turning into a even bigger headache.

                            Atleast they're easy to replace.

                            Comment


                            • #29
                              Originally posted by 85z28kid View Post
                              Damn Larry that's bad. Looks like this good deal is turning into a even bigger headache.

                              Atleast they're easy to replace.
                              Yea, I'll still be under new price, but not by much. Lol
                              sigpic
                              U.S. Army 1983-2005
                              11.20@122.37 1.51 60'

                              Originally posted by WMCCjames

                              "Plans Subject to change upon Sobering up"

                              Comment


                              • #30
                                Originally posted by Fox Slaughter View Post
                                How many splines are your axles?

                                I met a guy last week on Woodward that told me he was the first person ever to get a F Body BMR K member and a bunch of other stuff. He said he runs a Moser 12 bolt and it will hold 2500hp and if he could break it Moser said they would buy it back from him. I was like oh yeah considering a 9" and a Dana 60 are stronger and are only rated to ~1500hp.

                                Oh and his engine was stock. He didn't even put heads or a cam in it.
                                let me borror it. bet it only makes it 100 feet

                                Comment

                                Working...
                                X