WTB: 4th gen harness bar.

[MunsterZ28]

6LE charges about double what everything they make is worth, only because no one else competes with them on most of their stuff. I bought mine from Fred here, and I don't think he'll ever forgive me for what I bartered him down to @MunsterZ28

I'd also like to get one of their splitters but im not willing to pay even half of what they are charging.

yes i once paid the 6le price for one, a good product and [MENTION=254]JoeliusZ28[/MENTION] i dont even remember what i let it go for but i know you low balled me, sall good tho i have low balled my fair share of people. im not mad

[JoeliusZ28]

It won't work for giants like Joel but it will work for normal people.

Lol, hey thanks!

[landstuhltaylor]

IMO instead of using a harness bar just cheat with the seat. Push the seat further back than you would normally sit and then put the seatbelt on. Once it's tight push the seat back up into your normal driving position. It should be much tighter and actually hold you in pretty well. It won't work for giants like Joel but it will work for normal people.

[QuickTop]

Maybe @Superman09 would be willing to take on a special project. He's got the ability to do full exhausts so I think he can do the mandrel bends in tubing... I know it's not the same thing but it's worth a shot.

IIRC, I think there's a thread floating around where he had thought about building some. I don't remember where that left off.

Romeo Fab could probably make you one cheaper than the 6LE

Ill do some research and see if I can find a fab shop a little closer.

[bri2203]

do you ever call Joe?

Yes, I am waiting to get my seats installed for shoulder belt purposes. Then I will decide whether to take it to him or to this place in OH. I

[DETROITMUSCLE]

I agree with Joel, They are too expensive to buy from 6LE.

I am going to spend a little more and have a 4 point roll bar. It will weigh more but it will add structure and will be safer in an accident

do you ever call Joe?

[JoeliusZ28]

Romeo Fab could probably make you one cheaper than the 6LE

[1BADAIR]

But a bender for roll bar tubing isn't very much

[bri2203]

He's got the ability to do full exhausts so I think he can do the mandrel bends in tubing.

I would be shocked if Johnny had a manual pipe bender.
Most people who build mandrel exhaust buy the bends in bulk and assemble the exhaust. A mandrel bender is big money $40,000+

[meissen]

Nobody will be in the back there's no seats back there anyway. I like the purpose of the harness bar and don't need a roll cage. So if nobody has a used one it looks like I'll just have to cough up the cash..

Maybe [MENTION=393]Superman09[/MENTION] would be willing to take on a special project. He's got the ability to do full exhausts so I think he can do the mandrel bends in tubing... I know it's not the same thing but it's worth a shot.

[BP_Z28]

I'll see if I can dig up the article later tonight. In an issue of Camaro Performers, they installed one on their Camaro. Black Betty.. IIRC the price wasn't to bad either.

Agreed on the 6LE stuff. Ridiculously priced

[QuickTop]

Nobody will be in the back there's no seats back there anyway. I like the purpose of the harness bar and don't need a roll cage. So if nobody has a used one it looks like I'll just have to cough up the cash..

[landstuhltaylor]

I figure I'll skip the bar and just get a cage. In the mean time I will be using the seat adjuster to cheat.

[bri2203]

I agree with Joel, They are too expensive to buy from 6LE.

I am going to spend a little more and have a 4 point roll bar. It will weigh more but it will add structure and will be safer in an accident

[JoeliusZ28]

The 6LE bar mounts to the rear seat belt mounts, so youre good with that one too as long as you dont plan on anyone sitting back there... Probably shouldnt with a bar for their head to slam into anyway.