4th Gen rear axles 2:73 stock and 4:10

[Razmiblackz28]

1994 Camaro Z28 rear axles, no brakes

Stock 2:73 ratio complete rear end to bolt on and drive, limited slip, 60k miles, no brakes $100

Stock rear end with aftermarket 4.10 gears, limited slip, installed great upgrade for 6 speed T56 cars no brakes $200

Unknown old Ford 9" axle, center section, axles, and housing $50

Located in Lansing, MI

[bri2203]

either of them a posi? I am not interested but others it will the first thing people will ask.

[Razmiblackz28]

Both are limited slip, good point.
No brakes on either axle.

[Razmiblackz28]

Do an easy axle swap and save some cash and the hassle of a gear install.

Cheap back-up axles too!

[ragtop]

Do you have pics on the Stock 2:73 ratio complete rear end

[Razmiblackz28]

Bottom axle is 2.73

[Razmiblackz28]

Dropped prices!!

[Joedashredder93]

would it fit my 99' cause I am in desperate need of one due to whining

[Razmiblackz28]

would it fit my 99' cause I am in desperate need of one due to whining

It will 'fit' but I think the ABS is different.

[MunsterZ28]

do you happen to know the length of the ford 9?

[Razmiblackz28]

do you happen to know the length of the ford 9?

Just dropped a tape measure on it. It's about 61-1/2" wheel flange to wheel flange.

[Joedashredder93]

all I really need is the passenger side axle and gears

[Razmiblackz28]

all I really need is the passenger side axle and gears

Buy the 2.73 axle and your all set on the cheap.

[craig62989]

would my 323 gears out of my non posi fit on te 2.73 one ?

[Razmiblackz28]

would my 323 gears out of my non posi fit on te 2.73 one ?

Yes, but they would have to be set-up.

[Joedashredder93]

I'll talk it over with the old man. thanks

[craig62989]

Yes, but they would have to be set-up.

what do you mean set up ?

[sman]

No I dont believe they will fit, 3.23 is a 3 series carrier, and 3.08 and below is a 2 series. So you could put your gears in but youd have to use your center section(carrier), therefore loosing the posi.

By set up he means that the gears need to be properly shimmed and check the wear patteren, to my knowledge its not good practice to use a used set of gears in another axle because its almost impossible to get them to wear the exact same as they did in the last axle. IIRC.

[Joedashredder93]

would this be the same for me?

[craig62989]

thanks spencer im going to see what i can do to come up wit some money to buy the 273 one to put in my v6 , can i put my drums on it ?

[bud_light_zero2000]

thats what I need

[Razmiblackz28]

Correct. My reply was based on moving the gear set and carrier over to this housing. To use the 2 series limited slip you would need a ring gear spacer and I'd suggest finding a 3 series carrier instead.

Your gears and diff will fit this housing but will need an install kit.



No I dont believe they will fit, 3.23 is a 3 series carrier, and 3.08 and below is a 2 series. So you could put your gears in but youd have to use your center section(carrier), therefore loosing the posi.

By set up he means that the gears need to be properly shimmed and check the wear patteren, to my knowledge its not good practice to use a used set of gears in another axle because its almost impossible to get them to wear the exact same as they did in the last axle. IIRC.